مقارنة خصائص من مونيل K500 و مونيل 400 النيكل والنحاس سبائك
مونيل K500
1. مقدمة إلى مونيل K500٪ 3a
مونيل K5٪ 7 ب ٪ 7b10٪ 7d٪ 7d0 في الواقع لديه نفس نفس التآكل المقاومة ك Monel4٪ 7b٪ 7b13٪ 7d٪ 7d٪ 2c لكن لديه أعلى ميكانيكي قوة و صلابة من 400. هو أيضا لديه أفضل حار تآكل مقاومة و طويل الأجل تنظيمي استقرار. ومع ذلك٪ 2c ال اللدونة هو قليلا أقل من ذلك مونيل K500. مقارنة مع Monel400٪ 2c هذا سبيكة يحتوي على a كتلة كسر من 2.3٪ 25٪ 7e3.15٪ 25 ألومنيوم AL و 0.3٪ 25٪ 7e1.00٪ 25 تيتانيوم Ti. ال المبلغ المضافة هو مختلف في أماكن مختلفة.
2. مونيل K500 التطبيقات و الميزات٪ 3a
Monel K500 alloy has good low-temperature plasticity and toughness, so you won't find any difficulty in cold working. However, in terms of hot working, the forming temperature is generally between 871 and 1149 degrees, and the large deformation is between 1038 and 1149 degrees. However, we recommend that the appropriate temperature should be between 1093 degrees, the alloy solution annealing temperature is 793~971, and good comprehensive properties can be obtained. The temperature of hot-processed products should be 982 degrees, and the temperature of cold-processed products should be 1038 degrees, but the heating time should be shortened as much as possible. Most uses of Monel K500 alloy are the same as 400, but if there are applications other than 400, this alloy can be used. Monel K500 alloy is mainly used in pump shafts, impellers, conveyor scrapers, oil drill rings, strong components, valve parts and papermaking equipment. Squeegee blades, etc.
مونيل 400
1. مقدمة إلى Monel400٪ 3a
Monel400 is a nickel based مقاومة للتآكل سبيكة ذلك تم تم استخدامها في صناعة ل a طويلة time. It has good شامل خصائص و a wide range of uses. It has تصبح an لا غنى عنها سبيكة لأن من لها جيدة التآكل المقاومة. إنها كيميائية تكوين هو بشكل أساسي مؤلف من Ni٪ 2c 30٪ 25 Cu و a صغير كمية. يتكون من Fe (1٪ 25٪ 7b٪ 7b5٪ 7d٪ 7d٪ 25).
Corrosion resistance of Monel400: The corrosion resistance of Monel400 is generally superior to that of nickel and copper. It is more resistant to corrosion from reducing media than pure nickel, and is more resistant to corrosion from oxidizing media than pure copper. It has good performance in fresh water, sea water and light salt water. With its corrosion resistance, he can manufacture propellers and shafts, pump shafts, impellers and condensing heat exchangers and structural parts of the splash zone of oil production platforms. The corrosion resistance to H2SO4, H3PO4 and carbon is very good. In particular, it has good corrosion resistance against fluorine gas, H2SO4, Na2SO3, HF and their derivatives. But it is not available for H3PO4 and organic acids. HIC acid in HCl is only suitable for room temperature and concentration less than 15%. At the same time, it is more corrosion-resistant than copper-based alloys in seawater, has good resistance to seawater corrosion and chemical corrosion, and has strong resistance to chloride stress corrosion cracking. It is one of the few materials that can withstand HF. It is corrosion-resistant in H2SO4 with a concentration less than 85%. In most cases of water corrosion, not only the corrosion resistance is good, but also pitting corrosion, stress corrosion, etc. are rarely found, and the corrosion rate is less than 0.025mm/a. The highest temperature for continuous operation in air is generally around 600 degree . In high-temperature steam, the corrosion rate is less than 0.026mm/a. Due to the high nickel content of the alloy, it can withstand corrosion under anhydrous ammonia and ammoniation conditions below 585 degree . It has good corrosion resistance to chlorine salt, sulfide salt, HNO3 salt, carbonate, H2SO4 aluminum, H2SO4 ammonium, NH4Cl, and zinc chloride.
2. Monel400 التطبيقات و الميزات٪ 3a
تقريبي استخدامات Monel400 سبيكة٪ 3a مختلف حرارة تبادل معدات ٪ 2c غلاية تغذية ماء سخانات ٪ 2c خطوط أنابيب ٪ 2c حاويات ٪ 2c مضخات ٪ 2c صمامات ٪ 2c مهاوي ٪ 2c إلخ في البترول و الكيميائية المعالجة ٪ 2C مياه البحر تحلية المياه المعدات ٪ 2C الملح الإنتاج المعدات ٪ 2C المروحة مهاوي ٪ 2C البنزين و المياه الخزانات ٪ 2C إلخ .
